Crate Amplifiers Musical Instrument Amplifier VTX350H User Manual |
VTX350H
Three-Channel Guitar Amplifier
with Advanced Digital Signal
Processing
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4,5
The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
The DSP Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Storing Your Own Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Restoring the Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
More About The Save/Tap Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Using the Footswitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
DSP Factory Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10,11
Suggested Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12,13
DSP “Fill in the Blanks” (for User Presets) . . . . . . . . . . . . . . . . . . . . .14
System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequen-
cy energy and, if not installed and used in accordance with the instructions, may cause harmful interfer-
ence to radio communications. However, there is no guarantee that interference will not occur in a par-
ticular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device not expressly approved by SLM Electronics could void the user’s
authority to operate the equipment under FCC rules.
Declaration of Conformity
Manufacturer’s Name: SLM Electronics
Corporate Headquarters: 1901 Congressional Drive, St. Louis, Missouri 63146
Primary Production Facility: 700 Hwy 202 W, Yellville, Arkansas, 72687
Product Type: Audio Amplifier
Products meet the regulations for compliance marking under:
ETL standards UL6500, UL60065, or UL813
CSA standards E60065 or C22.2 No.1-M90
CE safety standard EN60065
CE EMC standards EN55103 or EN55013 and EN61000
C-tick designation Level 2, ABN #56748810738, ARBN# N222
KETI standard K60065 (limited model approval)
Compliance Support Contact: SLM Electronics, Attn: R&D Compliance Engineer
1901 Congressional Drive, St Louis, Missouri, 63146 • Tel.: 314-569-0141, Fax: 314-569-0175
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
Congratulations!
You are now the proud owner of the Crate VTX350H three-channel guitar amplifier
with Advanced Digital Signal Processing. This rugged amplifier combines outstanding
features with serious clean and distorted sounds. Dual DSP controls provide 15 mod-
ulation effects and 15 delay effects which can be combined for a wide variety of sounds.
The Tap/Save button allows you to manually set the tempo of many of the effects and
to save new DSP presets in the amplifier’s non-volatile memory. A separate Reverb
control adds even more to the array of effects.
A highly visible electronic tuner (with a Mute switch for silent tuning) allows you to
get tuned and stay in tune any time the amplifier is on. The rear panel Line In and Line
Out jacks allow you to connect additional equipment for even greater flexibility.
Channel switching, Tap/Save, and a second bank of DSP effects may be controlled
by means of the supplied four button footswitch.
Like all Crate products, your VTX350H amplifier is designed by musicians, and built
using only the best components. Extensive testing confirms that this amplifier is the
absolute best it can be.
In order to get the most out of your new amplifier, we strongly suggest that you read
the information contained in this guide before you begin playing.
And thank you for choosing Crate.
CAUTION
PRECAUCION
ATTENTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RIESGO DE CORRIENTAZO
NO ABRA
RISQUE D'ELECTROCUTION
NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOIS-
TURE. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
PRECAUCION: PARA REDUCIR EL RIESGO DE INCENDIOS
O
DESCARGAS
LA
ATTENTION: PROTÉGEZ CET APPAREIL DE LA PLUIE ET DE L'HUMIDITÉ
AFIN D'ÉVITER TOUT RISQUE D'INCENDIE OU D'ÉLECTROCUTION. POUR
REDUIRE D'ELECTROCUTION NE PAS ENLEVER LE COUVERCLE. AUCUNE
PIECE INTERNE N'EST REPRABLE PAR L'UTILISATEUR. POUR TOUTE
REPARATION, S'ADRESSER A UN TECHNICIEN QUALIFIE.
ELECTRICAS, NO PERMITA QUE ESTE APARATO QUEDE EXPUESTO
A
LLUVIA
O
LA HUMEDAD. PARA DISMINUOIR EL RIESGO DE CORRIENTAZO.
NO ABRA LA CUBIERTA. NO HAY PIEZAS ADENTRO QUE EL USARIO PUEDO
REPARAR DEJE TODO MANTENIMIENTO A LOS TECHNICOS CALIFICADOS.
IMPORTANT SAFETY INSTRUCTIONS
•
•
READ, FOLLOW, HEED, AND KEEP ALL INSTRUCTIONS AND WARNINGS.
DO NOT OPERATE NEAR ANY HEAT SOURCE AND DO NOT BLOCK ANY VENTILATION OPENINGS ON THIS APPARATUS. FOR PROPER OPERATION,
THIS UNIT REQUIRES 3” (75mm) OF WELL VENTILATED SPACE AROUND HEATSINKS AND OTHER AIR FLOW PROVISIONS IN THE CABINET.
•
•
•
DO NOT USE THIS APPARATUS NEAR SPLASHING, FALLING, SPRAYING, OR STANDING LIQUIDS.
CLEAN ONLY WITH LINT-FREE DAMP CLOTH AND DO NOT USE CLEANING AGENTS.
ONLY CONNECT POWER CORD TO A POLARIZED, SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRICAL CODES AND COMPATIBLE WITH
VOLTAGE, POWER, AND FREQUENCY REQUIREMENTS STATED ON THE REAR PANEL OF THE APPARATUS.
•
•
•
PROTECT THE POWER CORD FROM DAMAGE DUE TO BEING WALKED ON, PINCHED, OR STRAINED.
UNPLUG THE APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.
ONLY USE ATTACHMENTS, ACCESSORIES, STANDS, OR BRACKETS SPECIFIED BY THE MANUFACTURER FOR SAFE OPERA-
TION AND TO AVOID INJURY.
•
•
•
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK OR FIRE, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
SERVICE MUST BE PERFORMED BY QUALIFIED PERSONNEL.
OUR AMPLIFIERS ARE CAPABLE OF PRODUCING HIGH SOUND PRESSURE LEVELS. CONTINUED EXPOSURE TO HIGH SOUND PRESSURE LEVELS
CAN CAUSE PERMANENT HEARING IMPAIRMENT OR LOSS. USER CAUTION IS ADVISED AND EAR PROTECTION IS RECOMMENDED IF UNIT IS
OPERATED AT HIGH VOLUME.
•
WARNING: THIS UNIT REQUIRES A SAFETY GROUNDED OUTLET WIRED TO CURRENT ELECTRIC CODES HAVING THE LINE SUPPLY VOLTAGE,
POWER, AND FREQUENCY IDENTIFIED ON THE REAR OF THE UNIT. THE OUTLET MUST REMAIN ACCESSIBLE TO DISCONNECT THE UNIT IF A
FAULT SHOULD ARISE WHILE IN USE. THIS UNIT SHOULD BE UNPLUGGED WHEN NOT IN USE.
EXPLANATION OF GRAPHICAL SYMBOLS:
EXPLICACION DE SIMBOLOS GRAFICOS:
EXPLICATION DES SYMBÔLES GRAPHIQUES:
"IT IS NECESSARY FOR THE USER TO REFER TO THE INSTRUCTION MANUAL"
“ES NECESARIO QUE EL USUARIO SE REFIERA AL MANUAL DE INSTRUCCIONES.”
"REFERREZ-VOUS AU MANUAL D'UTILISATION"
"DANGEROUS VOLTAGE"
“VOLTAJE PELIGROSO”
"DANGER HAUTE TENSION"
=
=
3
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
The Front Panel:
1. POWER: Use this switch to turn the amplifier on (top of the switch depressed) and off (bottom
of the switch depressed). The switch illuminates when the power is on.
2. REVERB: Use this control to adjust the amount of digital reverb effect. In its fully counterclock-
wise position the signal will be “dry” (without any reverb). As you rotate the control clockwise the
amount of reverb increases.
3. TAP/SAVE (LED): This LED flashes in time with the tempo set by the Tap/Save button (#4), and
serves as a status indicator for certain DSP activities (see page 8).
NOTE: For some of the DSP effects, the Save/Tap LED remains illuminated. The Save/Tap LED does
not illuminate when the DSP knobs are set to the Bypass position.
4. TAP/SAVE: Use this pushbutton to set the tempo of many of the effects by tapping the button
repeatedly in time with the desired tempo. The Tap/Save button is also used to save DSP presets
and to restore the factory default DSP settings. Additional information about the Tap/Save button
is on pages 7 and 8.
5. DELAY: Use this control to select one of the fifteen digital delay effects. Complete information
about the DSP effects is on page 7.
6. EFFECTS: Use this control to select one of the fifteen digital modulation effects. Complete
information about the DSP effects is on page 7.
7. (ELETRONIC TUNER): The electronic tuner is active whenever the amplifier is turned on, pro-
viding constant, “real-time” tuning. The bottom row of LEDs indicate which note (string) is being
tuned. The top row of LEDs provides directional queues to facilitate quick and precise tuning of
your instrument. The indicated note (string) is properly tuned when only the center LED is illumi-
nated.
8. MUTE: This switch, when depressed, mutes the output signals at the Speaker jacks (#30) and
the Line out jack (#28), allowing you to silently tune or switch instruments. The adjacent yellow
LED illuminates when the Mute function is active.
9. 3 (CH 3 SELECT): This switch, when depressed, selects Channel 3 as the active channel. The
adjacent red LED illuminates when Channel 3 is active. Channel 3 features a high gain FlexWave
circuit for extreme distortion and sustain.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
10. HIGH: Use this control to adjust the high frequency level of Channel 3.
11. LEVEL: Use this control to adjust the output level of Channel 3.
12. MID: Use this control to adjust the midrange frequency level of Channel 3.
13. GAIN: Use this control to adjust the amount of distortion produced by Channel 3.
14. LOW: Use this control to adjust the low frequency level of Channel 3.
15. 2 (CH 2 SELECT): This switch, when depressed, selects Channel 2 as the active channel.
The adjacent yellow LED illuminates when Channel 2 is active. Channel 2 features a medium
gain FlexWave circuit for moderate distortion and “crunch.”
16. HIGH: Use this control to adjust the high frequency level of Channel 2.
17. LEVEL: Use this control to adjust the output level of Channel 2.
18. MID: Use this control to adjust the midrange frequency level of Channel 2.
19. GAIN: Use this control to adjust the amount of distortion produced by Channel 2.
20. LOW: Use this control to adjust the low frequency level of Channel 2.
21. 1 (CH 1 SELECT): This switch, when depressed, selects Channel 1 as the active channel.
The adjacent green LED illuminates when Channel 1 is active. Channel 1 features a low gain
FlexWave circuit for clean sounds or sounds with mild distortion.
22. HIGH: Use this control to adjust the high frequency level of Channel 1.
23. LEVEL: Use this control to adjust the output level of Channel 1.
24. MID: Use this control to adjust the midrange frequency level of Channel 1.
25. GAIN: Use this control to adjust the amount of distortion produced by Channel 1.
26. LOW: Use this control to adjust the low frequency level of Channel 1.
27. (INPUT): Use this jack to connect your guitar to the amplifier by means of a shielded instru-
ment cable.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
The Rear Panel:
28
29
30
31
32
28. LINE OUT: When using an external effects processor, connect this jack to the input of the effect by means of
a shielded signal cable. This jack also doubles as a source for a post-EQ preamp signal to send to a mixing board,
recorder, powered monitor or external amplifier.
29. LINE IN: When using an external effects processor, connect this jack to the output of the effect by means of a
shielded signal cable. This jack also doubles as a direct connection to the power amp, bypassing the input and pre-
amp stages. This is useful for “slaving” a pair of amplifiers together.
30. SPEAKERS: Use these jacks to connect the amplifier to your speaker(s) by means of speaker cables with
mono 1/4” plugs. These jacks are wired in parallel. Make sure that the combined impedance of your speakers is
equal to or greater than 2 ohms! Use the chart below to help determine parallel loads. If in doubt, ask your dealer.
CAB IMP
4 ohms
8 ohms
8 ohms
# CABS TOTAL IMP
CAB IMP
16 ohms
16 ohms
16 ohms
# CABS TOTAL IMP
2
2
4
2 ohms
4 ohms
2 ohms
2
4
8
8 ohms
4 ohms
2 ohms
31. FOOTSWITCH: Use this jack to connect the footswitch cable (5-conductor midi cable) to the four button
footswitch (supplied). This allows you to remotely switch between the channels, set tap tempos, save new presets,
and access a second set of DSP presets. (See page 9 for additional information.)
32. FUSE: The fuse protects the amplifier from damages caused by a faulty AC power source and/or other prob-
lems. If the fuse opens, replace it ONLY with the same size and type. If fuses continue to fail, check the AC source
– if the source is okay, contact your Crate dealer for service information.
33. AC LINE CORD (not shown): This grounded power cord is to be plugged into a grounded power outlet, wired
to current electrical codes and compatible with the voltage, power, and frequency requirements stated on the rear
panel. Do not attempt to defeat the safety ground connection.
WARNING: The speaker output of this unit can
exceed 10 Watts and could be a shock injury.
Connection to speakers should be performed by a
skilled person in compliance with local building
codes. Class 2 wiring is required for speaker
cables. Use of external speakers outside the rat-
ings stated at the speaker jack may result in a
shock injury or damage to the unit.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
VTX350H Three-Channel Guitar Amplifier with Advanced DSP
The DSP Section:
The VTX350H features DSP controls
for Reverb, Delay and Effects. Complete
information about the modulated and
delay effects is given below. The Delay
control selects the delay or echo effects.
All of these effects have their speed controlled by the Tap/Save button. The Effects con-
trol selects the “pitch modified” and wah effects. Many of these effects have their speed
controlled by the Tap/Save button. Additional information is provided on pages 5 and 10.
SIGNAL PATH FOR DELAY "EFFECTS 1, 2 & 3"
SIGNAL PATH FOR ALL OTHER EFFECTS
COMBINATIONS
EFFECTS
DELAY
DELAY
EFFECTS
DELAY:
NAME
DESCRIPTION
SAVE/TAP BUTTON CONTROLS:
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
time: .05–1 second
n/a
Single 1
Single 2
Single 3
Single 4
Echo 1
Echo 2
Echo 3
Echo 4
Tape 1
Tape 2
Tape 3
Tape 4
Effects 1
Effects 2
Effects 3
Ø
Single delay w/low level
Single delay w/medium level
Single delay w/high level
Single delay w/maximum level
Echo w/low level
Echo w/medium level
Echo w/high level
Echo w/maximum level
Tape echo w/low level
Tape echo w/medium level
Tape echo w/high level
Tape echo w/maximum level
Echo w/low level, before effect
Echo w/medium level, before effect
Echo w/high level, before effect
Bypass - no effect
EFFECTS:
NAME
DESCRIPTION
Chorus w/low depth
SAVE/TAP BUTTON CONTROLS:
speed: 1 cycle/tap - tap period: .05–1 second
speed: 1 cycle/tap - tap period: .05–1 second
speed: 1 cycle/tap - tap period: .05–1 second
speed: 4 cycle/tap - tap period: .05–1 second
speed: 4 cycle/tap - tap period: .05–1 second
speed: 4 cycle/tap - tap period: .05–1 second
speed: 2 cycle/tap - tap period: .05–1 second
speed: 2 cycle/tap - tap period: .05–1 second
speed: 2 cycle/tap - tap period: .05–1 second
speed: 1 cycle/tap - tap period: .05–1 second
speed: 1 cycle/tap - tap period: .05–1 second
speed: 1 cycle/tap - tap period: .05–1 second
n/a
Chorus 1
Chorus 2
Chorus 3
Flange 1
Flange 2
Flange 3
Phaser 1
Phaser 2
Phaser 3
Vibrato 1
Vibrato 2
Vibrato 3
Oct
Chorus w/medium depth
Chorus w/high depth
Flanger w/low depth
Flanger w/medium depth
Flanger w/high depth
Phaser w/low feedback
Phaser w/medium feedback
Phaser w/high feedback
Vibrato w/low depth
Vibrato w/medium depth
Vibrato w/high depth
Adds signal one octave lower
Touch-sensitive wah-wah
Inverted wah-wah
Wah
R-Wah
n/a
n/a
Ø
Bypass - no effect
n/a
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|